Circular hollow sections | Idea Statica Web Eshop

Failure mode method

In this chapter, component-based finite element method (CBFEM) for design of uniplanar welded Circular Hollow Sections (CHS) is verified to Failure Mode Method (FMM): T, X, and K-joints. In CBFEM, the design resistance is limited by reaching 5 % of strain or a force corresponding to 3% d₀ joint deformation, where d₀ is chord diameter. The resistance in FMM is generally determined by peak load or 3% d₀deformation limit, see (Lu et al. 1994). FMM is based on the principle of identifying modes that may cause joint failure. From the practical experience and experiments accomplished during the 70s and 80s, two modes of failure were identified for the CHS joints: chord plastification and chord punching shear. This calculation method is always limited to a probed geometry of joints. This means that different formulas always apply for each geometry. In the following studies, the welds are designed according to EN 1993‑1‑8:2006 not to be the weakest components in the joint.

Chord plastification

The design resistance of a CHS chord face can be determined using the method given by FMM model in Ch. 9 of prEN 1993-1-8:2020; see Fig. 7.1.1. The method is also given in ISO/FDIS 14346 and is described in more detail in (Wardenier et al. 2010). The design resistance of the axially loaded welded CHS joint is:

for T and Y joint

\[ N_{1,Rd} = C_f \frac{f_{y0} t_0^2}{\sin{\theta_1}} (2.6+17.7 \beta^2) \gamma^{0.2} Q_f / \gamma_{M5} \]

X joint

\[ N_{1,Rd} = C_f \frac{f_{y0} t_0^2}{\sin{\theta_1}} \left ( \frac{2.6+2.6 \beta}{1-0.7 \beta} \right ) \gamma^{0.15} Q_f / \gamma_{M5} \]

and for K gap joint

\[ N_{1,Rd} = C_f \frac{f_{y0} t_0^2}{\sin{\theta_1}} (1.65+13.2 \beta^{1.6}) \gamma^{0.3} \left [ 1+ \frac{1}{1.2+(g/t_0)^{0.8}} \right ] Q_f / \gamma_{M5} \]

where:

d_i – an overall diameter of CHS member i (i = 0, 1, 2 or 3)
f_yi – yield strength of member i (i = 0, 1, 2 or 3)
g – gap between braces of K joint
t_i – thickness of the wall of CHS member i (i = 0, 1, 2 or 3)

\[ \textsf{\textit{\footnotesize{Fig. 7.1.1 Examined failure mode – chord plastification}}}\]

Chord punching shear

(for \(d_i \le d_0 - 2 t_0\))

The design resistance of the axially loaded T, Y, X, and K joint of welded circular hollow sections for chord punching shear (Fig. 7.1.2) is:

\[ N_{1,Rd} = C_f \frac{f_{y0}}{\sqrt{3}} t_0 \pi d_i \frac{1+\sin{\theta_1}}{2 \sin^2{\theta_1}} / \gamma_{M5} \]

where:

d_i – overall diameter of CHS member i (i = 0,1,2 or 3)
t_i– thickness of the wall of CHS member i (i = 0,1,2 or 3)
f_y,i – yield strength of member i (i = 0,1,2 or 3)
\(\theta_i\) – included angle between brace member i and the chord (i = 1,2 or 3)

\[ \textsf{\textit{\footnotesize{Fig. 7.1.2 Examined failure mode – chord punching shear}}}\]

Chord shear

(for X joints, only if \(\cos{\theta_1} > \beta\))

The design resistance of the axially loaded X joint of welded circular hollow sections for chord shear, see Fig. 7.1.3, is:

\[ N_{1,Rd} = \frac{f_{y0}}{\sqrt{3}} \frac{(2/\pi A_0)}{\sin{\theta_1}} / \gamma_{M5} \]

where:

A_i – area of cross-section i (i = 0,1,2 or 3)
f_y,i – yield strength of member i (i = 0,1,2 or 3)
\(\theta_i\) – included angle between brace member i and the chord (i = 1,2 or 3)
N_i,Rd – design resistance of a joint expressed in terms of the internal axial force in member i ( = 0, 1, 2 or 3)

\[ \textsf{\textit{\footnotesize{Fig. 7.1.3 Examined failure mode - Chord shear}}}\]

Range of validity

CBFEM was verified for typical joints of the welded circular hollow sections. Range of validity for these joints is defined in Table 7.1.8 of prEN 1993-1-8:2020; see Tab 7.1.2. The same range of validity is applied to CBFEM model. Outside the range of validity of FMM, an experiment should be prepared for validation or verification performed for verification according to a validated research model.

Tab. 7.1.2 Range of validity for method of failure modes

General	\(0.2 \le \frac{d_i}{d_0} \le 1.0 \)	\( \theta_i \ge 30^{\circ} \)	\(-0.55 \le \frac{e}{d_0} \le 0.25 \)
	\(g \ge t_1+t_2 \)	\(f_{yi} \le f_{y0} \)	\( t_i \le t_0 \)

Chord	Compression	Class 1 or 2 and \(10 \le d_0 / t_0 \le 50 \) (but for X joints: \( d_0/t_0 \le 40 \))
	Tension	\(10 \le d_0 / t_0 \le 50 \) (but for X joints: \( d_0/t_0 \le 40 \))
CHS braces	Compression	Class 1 or 2 and \(d_i / t_i \le 50\)
	Tension	\(d_i / t_i \le 50 \)

Uniplanar T and Y-CHS joint

Overview of the considered examples in the study is given in Tab. 7.1.3. Selected cases cover a wide range of joint geometric ratios. Geometry of the joints with dimensions is shown in Fig. 7.1.2. In the selected cases, the joints failed according to the FMM by the chord plastification or punching shear.

\[ \textsf{\textit{\footnotesize{Fig. 7.1.4 Dimensions of T/Y joint}}}\]

Tab. 7.1.3 Examples overview

Example	Chord	Brace	Angles		Material
	Section	Section	\(\theta\)	fy	fu	E
			[°]	[MPa]	[MPa]	[GPa]
1	CHS219.1/5.0	CHS48.3/5.0	90	355	490	210
2	CHS219.1/5.0	CHS114.3/6.3	90	355	490	210
3	CHS219.1/6.3	CHS114.3/6.3	90	355	490	210
4	CHS219.1/10.0	CHS60.3/5.0	90	355	490	210
5	CHS219.1/12.5	CHS168.3/10.0	90	355	490	210
6	CHS219.1/8.0	CHS48.3/5.0	90	355	490	210

Verification of resistance

The results of the method based on FMM are compared with the results of CBFEM. The comparison is focused on the resistance and design failure mode. The results are presented in Tab. 7.1.4.

The study shows a good agreement for the applied load cases. The results are summarized in a diagram comparing CBFEM’s and FMM’s design resistances; see Fig. 7.1.5. The results show that the difference between the two calculation methods is in all cases less than 14%.

Tab. 7.1.4 Comparison of design resistances for loading in tension/compression: prediction by CBFEM and FMM

\[ \textsf{\textit{\footnotesize{Fig. 7.1.5 Verification of CBFEM to EN 1993-1-8 for the uniplanar CHS T and Y-joint}}}\]

\[ \textsf{\textit{\footnotesize{Fig. 7.1.6 Verification of CBFEM to Fpr EN 1993-1-8 for the uniplanar CHS T and Y-joint}}}\]

Benchmark example

Inputs

Chord

Steel S355
Section CHS219.1/5.0

Brace

Steel S355
Sections CHS48.3/5.0
Angle between the brace member and the chord 90°

Weld

Butt weld around the brace

Loaded

By force to brace in compression

Mesh size

64 elements along surface of the circular hollow member

Outputs

The design resistance in compression is N_Rd = 56.3 kN
The design failure mode is chord plastification

\[ \textsf{\textit{\footnotesize{Fig. 7.1.6a Boundary conditions for the uniplanar CHS T and Y-joint}}}\]

Otevřít v aplikaci Viewer Stáhnout

Uniplanar X-CHS joint

Overview of the considered examples in the study is given in Tab. 7.1.5. Selected cases cover a wide range of joint geometric ratios. Geometry of the joints with dimensions is shown in Fig. 7.1.6. In the selected cases, the joints failed according to the FMM by the chord plastification or punching shear.

\[ \textsf{\textit{\footnotesize{Fig. 7.1.7 Dimensions of X joint}}}\]

Tab. 7.1.5 Examples overview

Example	Chord	Brace	Angles		Material
	Section	Section	\(\theta\)	fy	fu	E
			[°]	[MPa]	[MPa]	[GPa]
1	CHS219.1/6.3	CHS60.3/5.0	90	355	490	210
2	CHS219.1/8.0	CHS76.1/5.0	90	355	490	210
3	CHS219.1/10.0	CHS139.7/10.0	90	355	490	210
4	CHS219.1/12.5	CHS114.3/6.3	90	355	490	210
5	CHS219.1/10.0	CHS76.1/5.0	90	355	490	210
6	CHS219.1/8.0	CHS114.3/6.3	90	355	490	210
7	CHS219.1/6.3	CHS48.3/5.0	60	355	490	210
8	CHS219.1/6.3	CHS114.3/6.3	60	355	490	210
9	CHS219.1/8.0	CHS60.3/5.0	60	355	490	210
10	CHS219.1/10.0	CHS114.3/6.3	60	355	490	210
11	CHS219.1/12.5	CHS139.7/10.0	60	355	490	210
12	CHS219.1/8.0	CHS139.7/10.0	60	355	490	210
13	CHS219.1/6.3	CHS48.3/5.0	30	355	490	210
14	CHS219.1/6.3	CHS193.7/12.5	30	355	490	210
15	CHS219.1/6.3	CHS219.1/12.5	30	355	490	210
16	CHS219.1/8.0	CHS76.1/5.0	30	355	490	210
17

Verification of resistance

The results of CBFEM are compared with the results of FMM. The comparison is focused on the resistance and design failure mode. The results are presented in Tab. 7.1.6.

Tab. 7.1.6 Comparison of results of prediction by CBFEM and FMM

The study shows a good agreement for most of the applied load cases. The results are summarized in a diagram comparing CBFEM’s and FMM’s design resistances; see Fig. 7.1.7. The results show that the difference between the two calculation methods is in most cases less than 13%.

\[ \textsf{\textit{\footnotesize{Fig. 7.1.8 Verification of CBFEM to EN 1993-1-8 for the uniplanar CHS X- joint}}}\]

\[ \textsf{\textit{\footnotesize{Fig. 7.1.9 Verification of CBFEM to Fpr EN 1993-1-8 for the uniplanar CHS X-joint}}}\]

Benchmark example

Inputs

Chord

Steel S355
Section CHS219.1/6,3

Brace

Steel S355
Sections CHS60,3/5,0
Angle between the brace member and the chord 90°

Weld

Butt weld around the brace

Loaded

By force to brace in compression

Mesh size

64 elements along surface of the circular hollow member

Outputs

The design resistance in compression is N_Rd = 103.9 kN
The design failure mode is chord plastification

\[ \textsf{\textit{\footnotesize{Fig. 7.1.9a Boundary conditions for the uniplanar CHS X-joint}}}\]

Otevřít v aplikaci Viewer Stáhnout

Uniplanar K-CHS joint

Overview of the considered examples in the study is given in Tab. 7.1.7. Selected cases cover a wide range of joint geometric ratios. Geometry of the joints with dimensions is shown in Fig. 7.1.8. In the selected cases, the joints failed according to the method based on the failure modes (FMM) by the chord plastification or punching shear.

Tab. 7.1.7 Examples overview

Example	Chord	Brace	Gap	Angles		Material
	Section	Section	g	\(\theta\)	fy	fu	E
			[mm]	[°]	[MPa]	[MPa]	[GPa]
1	CHS219,1/8,0	CHS88,9/5,0	23.8	60	355	490	210
2	CHS219,1/12,5	CHS88,9/5,0	23.8	60	355	490	210
3	CHS219,1/5,0	CHS88,9/5,0	23.8	60	355	490	210
4	CHS219,1/10,0	CHS60,3/5,0	56.9	60	355	490	210
5	CHS219,1/6,3	CHS88,9/5,0	23.8	60	355	490	210
6	CHS219,1/6,3	CHS60,3/5,0	56.9	60	355	490	210
7	CHS219,1/8,0	CHS76,1/5,0	38.6	60	355	490	210
8	CHS219,1/10,0	CHS76,1/5,0	38.6	60	355	490	210
9	CHS219,1/6.3	CHS48,3/65,0	70.7	60	355	490	210
10	CHS219,1/12,5	CHS48,3/5,0	70.7	60	355	490	210

\[ \textsf{\textit{\footnotesize{Fig. 7.1.10 Dimensions of K joint}}}\]

Verification of resistance

The results of the method based on failure modes (FMM) are compared with the results of CBFEM. The comparison is focused on the resistance and design failure mode. The results are presented in Tab. 7.1.8 and in Fig. 7.1.9.

Tab. 7.1.8 Comparison of results of design resistances by CBFEM and FMM

The study shows a good agreement for the applied load cases. The results are summarized in a diagram comparing CBFEM’s and FMM’s design resistances; see Fig. 7.1.6. The results show that the difference between the two calculation methods is in all cases less than 12 %.